Aller au contenu

Procédure lire les codes défauts sur un 3.0l sans le consult


Papy Mouzo

Messages recommandés

Voilà une prcédure qui est fort utile quand on a un voyant diag allumé dans le désert, et qu'on ne sait pas d'ùu ça vient ( désolé, c'est en Anglais.. ) :

 

 

Displaying the ECU fault codes. (ZD30) 3.0ltr TDi

 

1.Ensure that the battery is fully charged and that the engine is at normal operating temperature.

 

2.Ensure all accessories are switched off.

 

3.Switch the ignition On but do not start the engine.

 

4.Bridge terminals 8 (IGN) and 1 (CHK) on the diagnosis connector. The engine waring lamp should extinguish.

 

Connector diagram (looking front on) it looks like a wiring plug rectangle shape.

 

Top row

16,15,14,13,12,11,10,9

8,7,6,5,4,3,2,1

Bottom row

 

Bridging 8 (IGN) and 1 (CHK) with piece of wire (just push it into the slot)

 

5.Wait at least 2 seconds and then remove the wire bridging the terminals of the diagnosis connector. Any stored fault codes should now be able to be read.

 

6.Read the codes by counting the number of flashes of the Check Engine warning lamp. The code numbers are displayed as sets of separated by a 2.1 second pause. Each set comprises a series of 0.6 second flashes, a 0.9 second pause and a further series of 0.3 second flashes. The first set represents the first 2 digits of the code and the second set represents the last 2 digits.

 

Example 1. Code 0102 (Air Flow sensor) would be shown as one 0.6 second flash, a 0.9 second pause and two 0.3 second flashes.

 

Example 2. Code 1004 (Injection Pump fuel cut out system) would be shown as ten 0.6 second flashes, a 0.9 second pause and four 0.3 second flashes.

 

Note: To cease retrieving codes or to read codes again, turn the ignition Off and wait at least ten seconds before restarting the above procedure if necessary.

-----------------------------------------------------

Clearing Fault Codes:

 

1.After reading the fault codes as described, reconnect the wire bridging terminals 8 (IGN) and 1 (CHK) while the ignition is still On.

 

2.Wait at least two seconds and then remove the wire bridging the terminals. Any stored codes should now be erased.

 

Note: Fault codes are also erased if the battery is disconnected for more than 24 hours.

 

3.Road test the vehicle and check that there are no fault codes stored.

 

Fault codes

0102 Air Flow Sensor

0103 Coolant temp sender

0104 Vehicle speed sensor

0203 Throttle pedal switch

0208 Cooling Fan control

0301 Engine ECU

0402 Fuel temperature sensor

0403 Throttle pedal position sensor

0406* Intake air volume VNC system

0407 Crankshaft position sensor

0502* Battery voltage

0504 Auto Trans communication line

0701 Injection Pump –cam ring position sensor

0702 Injection Pump –TDC pulse sensor

0703 Injection Pump communication line

0704 Injection Pump –spill valve

0705 Injection Pump –ECU

0706 Injection Pump –spill valve

0707 Injection Pump injection timing control

0802 Engine ECU

0804* Engine ECU

0807 Stop lamp switch

0901 Engine ECU

0902 Engine ECU relay

0903* Engine ECU

0905 Intake air pressure sensor

1003 EGR volume control valve

1004 Injection Pump –fuel cut out system

 

* These codes do not illuminate the Check Engine warning lamp.

Lien vers le commentaire
Partager sur d’autres sites

×
×
  • Créer...

Information importante

Ce site web utilise les cookies pour améliorer votre expérience de navigation.